{"product_id":"taylor-50gt-v2-goped-gsr46-engine-complete-package","title":"TAYLOR 50GT V2 GOPED GSR46 Engine Complete Package","description":"\u003cp\u003eOur very torquey mid sized Big Bore Billet Reed Engine! This has turned into our best seller and is kept partially in stock on shorter lead times as suits all platforms and turns heads everywhere by sheer power output for the size.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePlease note all Big Block engines are built to order, expect circa 7 - 14 days for shipment.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe engine comes as a complete package, for full hassle free drop in fitment without any compatibility issues. You will just need to sort your throttle linkage out, we recommend a Slitzell WJ Linkage billet piece which bolts onto your carb.\u003c\/p\u003e\n\u003cp\u003eCustom Anodising is available in all colours and even Dual Colour Splash anodising! Please just get in touch after placing an order to discuss.\u003c\/p\u003e\n\u003cp\u003eThe package includes the following:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e50cc Billet Reed engine (40mm Bore x 39.6mm Stroke)\u003c\/li\u003e\n\u003cli\u003eTAYLOR GT CYLINDER (Insane torque output with staged triple exhaust port)\u003c\/li\u003e\n\u003cli\u003eChoice of Stock Cast head (lower compression and painted black) or Billet head (more torque)\u003c\/li\u003e\n\u003cli\u003e78mm 3-Shoe GO-PED CLUTCH SYSTEM\u003c\/li\u003e\n\u003cli\u003eFits straight onto the stock Ram Clutch bell housing and transmission for easy swap.\u003c\/li\u003e\n\u003cli\u003eOppama Japanese Ignition System\u003c\/li\u003e\n\u003cli\u003eTAYLOR BILLET HD PULL STARTER\u003c\/li\u003e\n\u003cli\u003eTAYLOR \u003ca rel=\"noopener\" title=\"Taylor RC Billet High RPM Reed Valve\" href=\"https:\/\/taylorrc.co.uk\/products\/taylor-billet-high-rpm-reed-valve\" target=\"_blank\"\u003eBillet High RPM Reed Valve\u003c\/a\u003e with Carbon Fiber Petals\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eFitted as standard with the WJ146 Big bore carb\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/taylorrc.co.uk\/products\/dt1-premium-foam-pre-oiled-air-filter\" title=\"DT1 High Performance Air Filter\" rel=\"noopener\" target=\"_blank\"\u003eDT1 Dual layer\u003c\/a\u003e foam filter\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eTAYLOR BIG BORE RAMINATOR EXHAUST and fitting kit.\u003c\/li\u003e\n\u003cli\u003eTank Risers\u003c\/li\u003e\n\u003cli\u003eCustom Throttle cable linkage bracket\u003c\/li\u003e\n\u003cli\u003eCustom Billet RH and LH engine brackets to replace stock engine brackets.\u003c\/li\u003e\n\u003cli\u003eThe famous TAYLOR Official Hat\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe 50GT fits almost the same as our 80cc Monster without the need to change the transmission. See install video by \u003ca href=\"https:\/\/youtu.be\/97yjgpOPBf0?si=RkPfiMjNWrV925jL\"\u003eRC Sparks on YouTube\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003eFitment into the Primal Raminator is fairly straightforward. Once you have removed the stock engine and pipe, also remove the centre top cross over link bar between the two side chassis plates.\u003c\/p\u003e\n\u003cp\u003eWhile the stock engine is out, we highly recommend cutting out a section of the side chassis plate next to the pull starter so that you can fit the engine (or even the stock engine) Without having to remove the pull starter or remove the side chassis plate itself. (see photo above with section cut out around the pull starter).\u003c\/p\u003e\n\u003cp\u003eThen the engine itself can drop in and bolt up with the supplied engine brackets (fitment shown in pics).\u003c\/p\u003e\n\u003cp\u003eAs mentioned above, if you cut your chassis it will drop in, if not, remove the pull start side chassis plate and then there is room to fit. Fit all the engine mounting bolts supplied. Next you can hook up the throttle linkage cable onto the big bore WJ71 carb. Simply remove the linkage cable hole from the stock carb by popping the bracket off and removing the E clip. Then put this piece onto the Hole cut out in the WJ71 Carb arm as shown in photos.\u003c\/p\u003e\n\u003cp\u003eFinally you can fit the cable to the supplied holder bracket and adjust to suit. (again see photos) The last step is to fit the exhaust mounting bracket to the car ready to support the pipe. (the main belly section of the pipe fits to the car AFTER the body has been fitted - slide in through the gap at back of the roll over bar and into place). Then its as simple as two retaining springs and the one nut on the rubber mount!\u003c\/p\u003e","brand":"Taylor RC","offers":[{"title":"Standard Cast Head","offer_id":62701110067587,"sku":null,"price":1575.0,"currency_code":"GBP","in_stock":true},{"title":"Add Billet Head (+75.00)","offer_id":62701110165891,"sku":null,"price":1650.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0677\/0550\/3978\/files\/taylor-rc-50gt-v2-goped-gsr46-engine-side-view.png?v=1790509642","url":"https:\/\/taylorrc.co.uk\/products\/taylor-50gt-v2-goped-gsr46-engine-complete-package","provider":"Taylor RC","version":"1.0","type":"link"}